MARC details
| 000 -LEADER |
|---|
| fixed length control field |
02402nam a2200241 4500 |
| 008 - FIXED-LENGTH DATA ELEMENTS--GENERAL INFORMATION |
|---|
| fixed length control field |
250510t2020 |||ado|g m||| 00| 0 eng d |
| 040 ## - CATALOGING SOURCE |
|---|
| Original cataloging agency |
Universiti Teknologi Brunei |
| Language of cataloging |
eng |
| Transcribing agency |
UTB |
| 084 ## - BOOK Call Number |
|---|
| Classification number |
UTB 120 THESIS REPORTS & DISSERTATION |
| -- |
RTDS 379 |
| 100 1# - MAIN ENTRY--PERSONAL NAME |
|---|
| Personal name |
Muhammad Haziq Bin Haji Awang Jaafar, |
| Relator term |
author. |
| 245 10 - TITLE STATEMENT |
|---|
| Title |
Eco-Friendly Machining Of Marine Grade AISI 316 Stainless Steel / |
| Statement of responsibility, etc. |
Muhammad Haziq Bin Haji Awang Jaafar. |
| 260 ## - PUBLICATION, DISTRIBUTION, ETC. (IMPRINT) |
|---|
| Place of publication, distribution, etc. |
Bandar Seri Begawan : |
| Name of publisher, distributor, etc. |
Universiti Teknologi Brunei, |
| Date of publication, distribution, etc. |
©2022. |
| 300 ## - PHYSICAL DESCRIPTION |
|---|
| Extent |
94 pages : |
| Other physical details |
color illustrations, photos, charts ; |
| Dimensions |
30 cm. |
| 500 ## - GENERAL NOTE |
|---|
| General note |
A thesis submitted to The Universiti Teknologi Brunei (UTB) in partial fulfillment of the requirements for the degree of Master of Science (MSc) in Mechanical Engineering. |
| 500 ## - GENERAL NOTE |
|---|
| General note |
ABSTRACT<br/>Milling AISI 316 stainless steel conventionally employs cutting fluids to reduce high-temperature generation associated with higher cutting speed, feed rate, and depth of cut. Unfortunately, cutting fluids can cause several issues in terms of the environment, health, and production costs. This study aims to conduct quantitative experimental research on the effectiveness of minimum quantity lubrication in AISI 316 stainless steel milling. Taguchi's orthogonal array was used in this experiment, which was found to significantly reduce the number of experiments required compared to a full factorial design. In addition, the signal-to-noise ratio, ANOVA, linear regression analysis, and confirmation test were performed. The spindle speed, feed rate, depth of cut, and flow rate of 1500 rpm, 360 mm/min, 0.2 mm, and 200 mL/h were the best parameters for achieving low surface roughness. Spindle speed, feed rate, depth of cut, and flow rate of 500 rpm, 360 mm/min, 0.1 mm, and 40000 mL/h, respectively, were optimal conditions for obtaining low burr height. The most significant parameters affecting surface roughness and burr height were spindle speed and depth of cut, respectively. |
| 502 ## - Dissertation Note |
|---|
| Dissertation Note |
Thesis (Degree) -Universiti Teknologi Brunei, 2022. |
| 610 #4 - SUBJECT ADDED ENTRY--CORPORATE NAME |
|---|
| Corporate name or jurisdiction name as entry element |
Universiti Teknologi Brunei |
| General subdivision |
Dissertations. |
| 650 #4 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Thesis writing. |
| 650 #4 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Stainless steel |
| General subdivision |
Machining. |
| 650 #4 - SUBJECT ADDED ENTRY--TOPICAL TERM |
|---|
| Topical term or geographic name entry element |
Austenitic stainless steel. |
| 700 1# - ADDED ENTRY--PERSONAL NAME |
|---|
| Titles and other words associated with a name |
Mohammad Yeakub Ali, Prof. Ir. Dr., |
| Relator term |
supervisor. |
| 942 ## - ADDED ENTRY ELEMENTS (KOHA) |
|---|
| Source of classification or shelving scheme |
Dewey Decimal Classification |
| Koha item type |
Reports, Thesis & Dissertation Students |
| 998 ## - LOCAL CONTROL INFORMATION (RLIN) |
|---|
| Internal field |
Reports, Thesis & Dissertation |
| CC (RLIN) |
850375 : 002226 c.1_UTB |
| Internal field |
Universiti Teknologi Brunei |
